SKID SAFE

A unique water based salt solution which degreases and cleans the heaviest soiled concrete surfaces like new. It works by penetrating the pores and releasing the trapped dirt inside. That way, after rinsing with water, the loosened grime washes off, leaving the original masonry surface clean, hard and intact. It also deposits a fine frosting which when sealed with our SKID SAFE and ND AGGREGATE™ will ensure the proper adhesion of SKID SAFE Water Based Sealer/Finish. Our ND AGGREGATE™ will create TRUE TRACTION - a non slip surface without affecting the aesthetics of the concrete, dyes, or paints.

Use CONCRETE BOND & CLEAN™ to clean all unsealed concrete surfaces:
- garages and driveways
- sidewalks and walkways
- warehouses and other indoor/outdoor concrete areas
- dirty walls, and even whole buildings
- removes all chewing gum stains after chewing gum is removed from sidewalks and concrete

CONCRETE BOND & CLEAN™ is very easy to use straight from the container without the need for scrubbing!

The spread rate will range from 150 sq. ft.-250 sq.ft. per gallon
1. Apply the product to the entire area needing cleaning.
2. Wait between 30-60 minutes as determined by your Patch Test for the product to work.
3. Rinse the area with water or powerwash the area. No brushing or scrubbing is necessary.
4. Allow the cleaned concrete area to dry out thoroughly before sealing with SKID SAFE and ND AGGREGATE™! We suggest a 24 hour drying time to allow all moisture within the concrete to dry out before sealing.

This innovative product is far less costly to use than shot blasting as commonly used on concrete, and it is more effective and safer than toxic, acid based products that etch and damage cleaned surfaces. This product does not contain Hydrofluoric acid, Hydrochloric acid, Muriatic acid or Sodium Hydroxide as some other products do.

CONCRETE BOND & CLEAN™ also creates perfect adhesion for SKID SAFE Water Based Sealer/Finish (ASTM C 1028 Dry: COF=.81; Wet: COF = .77) as applied on any type of slick surface for the purpose of providing very high slip resistance, and or, traction (when fine aggregate is added to the fresh application of SKID SAFE).

Use our SUPER BOND & CLEAN™ to create proper adhesion of SKID SAFE to all ceramic tile floors and walls, use CONCRETE BOND & CLEAN™ before sealing any unsealed concrete.

Application Directions:

Adjacent areas must be properly protected when using this product. Though harmless to most building surfaces, the damage CONCRETE BOND & CLEAN™ causes to glass, soft metal is considered permanent. Cover all nearby windows and aluminum with plastic sheeting and plastic tape. Also, protect vegetation. CONCRETE BOND & CLEAN™ turns foliage brown on contact, and if drawn up through plants roots, it dehydrates and can kill them. Cover plants with plastic sheeting to keep concentrated CONCRETE BOND & CLEAN™ off foliage, and protect roots by either containing the rinse or trenching it away. DO NOT USE ON PREVIOUSLY SEALED CONCRETE WITHOUT STRIPPING OFF THE OLD SEAL.

1. Do the Patch Test on a small inconspicuous area to confirm compatibility and to determine how long you need to let CONCRETE BOND & CLEAN™ soak to achieve the appearance that you like. Apply the product to the entire area needing cleaning. Greasy/oily concrete requires brush agitation of Concrete Bond & Clean™. Use a deck brush to agitate the surface and allow CONCRETE BOND & CLEAN™ to get down into the pores of the floor. Soiled/dirty concrete does not require brushing! The soaking time is usually between 30 - 60 minutes, but you must determine it by yourself by observation of your surfaces. Only then, once you have established that CONCRETE BOND & CLEAN™ is suitable for you, and you know how long you need to have it soaking proceed with the entire job area.
2. Brush, roll or spray CONCRETE BOND & CLEAN™ on to a dry surface, thoroughly wetting it.
3. Allow CONCRETE BOND & CLEAN™ enough time to work, leaving it on as long as your Patch Test determined.
4. Rinse the loosened grime from the surface with clean water. Pressure washer is usually the easiest and the most convenient way to do this work.
5. Allow the cleaned concrete to dry out thoroughly about 24 hours before sealing with SKID SAFE Water Based Sealer/Finish and ND AGGREGATE™ to ensure that moisture is not trapped below the surface.
Spraying on CONCRETE BOND & CLEAN™:
Avoid wind drifts and soak the cleaned surface well. A pump up sprayer or low pressure electric prep pump (50 to 60 psi), outfitted with a saturation nozzle (fan shaped spray) works best for this operation. Do not run CONCRETE BOND & CLEAN™ downstream through a pressure washer, because this dilutes it nor by applying it with a low-pressure airless sprayer, because they atomize solutions.

TOOLS TO USE:
A power-painting roller can be an ideal way to apply CONCRETE BOND & CLEAN™ on walks, driveways, patios, plazas or other large flat areas. Units, fitted with large commercial size rollers and mounted on extension handles, allow users to rapidly apply material while completely eliminating overspray.

LIMITATIONS:
Though CONCRETE BOND & CLEAN™ cleans virtually anything, which affects the appearance of concrete, it is not designed to remove graffiti or strip paint, nor does it remove hardened crusts and some types of staining which occur on masonry.

SAFETY PRECAUTIONS:
Wear rubber gloves and safety goggles, when handling CONCRETE BOND & CLEAN™. Ventilate enclosed areas. If CONCRETE BOND & CLEAN™ gets on skin or into eyes, rinse immediately with water. See Material Safety Data Sheet for more detailed hazard evaluation and safety information.
CONCRETE BOND & CLEAN™ is readily biodegradable and releases no V.O.C.s. When used properly, it poses no threat to the environment. Dispose of all wastes safely according to federal, state and local regulations.
FIRST AID: Rinse eyes thoroughly for 15 minutes and seek medical attention. Rinse skin thoroughly with running water. If ingested drink large amounts of water or milk, DO NOT INDUCE VOMITING, and seek medical attention.
LIMITATION OF LIABILITY: The user accepts full responsibility and risk in testing this product for the particular application. In no event shall NEW DIMENSIONS Solutions, LLC be liable for consequential or incidental damages exceeding the cost of this product.

NOTICE: DO NOT STORE NOR USE THIS PRODUCT BELOW 45° F! IF THIS PRODUCT IS BELOW 45° F, REHEAT BEFORE USE AND ONLY USE IT WHEN THE TEMPERATURE IS OVER 45° F.

 

Order Also These Products With CONCRETE BOND & CLEAN™:

SKID SAFE - Together with ND AGGREGATE™ Creates Non Slip Floor Finish With True Traction

ND AGGREGATE™ - Creates Non Slip Floor Finish With True TractioN

SUPER BOND & CLEAN™ - Creates Proper Adhesion of SKID SAFE to Ceramic Tiles

CLICK PRICE BELOW TO ORDER:

Always test our products on a small area first to insure adequate surface preparation, compatibility and desired results. Do not use SKID SAFE on areas that will be under standing water over 5 days. We make no claim to prevent slip/fall accidents when using SKID SAFE! The user is provided additional slip resistance, and or, true traction through the proper use of our products-only. We encourage all to thoroughly test and evaluate this product, and our other fine products, for suitability of purpose and function.

OUR PRODUCT PERFORMANCE GUARANTEE:

We guarantee your satisfaction when ordering our products in Quarts or smaller sizes (including all KITS) and 1 lb ND AGGREGATE™ for 30 days from the date that you receive your order. This guarantee is limited to one unit of each product. The purpose of this guarantee is to allow our customers at no cost (besides the cost of shipping/handling) to test our products for suitability before ordering larger quantities. Testing our products on a small inconspicuous area will demonstrate its performance for your end use, and it will allow you to determine the exact spread rates of our sealers/finishes so that you will know how much product you need for your project. Contact us to complete our RETURN/REFUND FORM so that we may learn about your reasons for a return and properly credit your credit card when we authorize your request. Our form will be emailed to you. Provide an accurate email address. This Guarantee does not cover any of our products in gallon, or larges sizes; it covers only quart sizes and 1 lb bags of ND AGGREGATE™, and is limited to one unit per product.

FIVE YEAR WARRANTY:

Your purchase of any of our primers/sealers/finishes/coatings are warranted to perform according to our specifications when applied and maintained according to our directions for 5 years. This warranty does not cover: misuse, misapplication, poor maintenance and high gloss. Your rights under this warranty are not transferable. Only the original buyer may file a claim with us under this warranty. If we determine the validity of a claim under this warranty, we will refund or replace the product(s) at your option less the time that the product(s) performed from the 5 year period. Example: If the product performed for 2.5 years, you could receive a refund of half the product cost, or replace the product at a credit of half of the List Price towards replacement.

LIMITATION OF LIABILITY:

You understand and agree that the owners of this site shall not be liable for any direct, indirect, incidental, consequential or exemplary damages, including but not limited to, damages for loss of profits, data or other intangible losses (even if the owners of this site have been advised of the possibility of such damages), resulting from the use or the inability to use the product(s) and or service(s) or any misuse of the product(s) and or service(s) in a manner not in accordance with their intended use. The user assumes full responsibility and risk in testing this product for the particular application and for determination of proper disposal method of chemical residues and cleaning implements according to State and Federal regulations. In no event shall New Dimensions Solutions, LLC be liable for consequential or incidental damages exceeding the cost of this product.