Manufacturer - Exclusive Distributor Of Unique And Superior Chemical Product Technology Since 1986
|
|
ONE COAT™ features a very low odor, very high spread rate, and years of lasting protection. ONE COAT™ also stainproofs and waterproofs. It is safe and pleasant to use as directed. Here are some main applications: 1. ONE
COAT™ is a paint protector and paint
restorer.
Use it to restore the pigment of faded, oxidized house paint and other paints. 4 coats produce an amazing new appearance - saving an owner the cost of repainting old paint that isn't damaged. Paint won't fade for many years (whether it is new or old) when sealed with ONE COAT™. It really should be used to seal all new paint once it is dry which will prevent the paint from fading peeling, flaking, chipping or cracking for many years. ONE COAT™ is also ideal for sealing line paint in parking garages, and for sealing curb paint. Exterior house paint sealed with ONE
COAT™ will save you several house painting
cycles. 3. Use ONE COAT™ to seal virtually anything "off the floor": walls, furniture, objects, such as plastics, chairs, desks, all metals, etc - new or used. Use 4 coats for the highest gloss and best protection. |
ONE COAT™ is available in both
a high gloss and in a satin/matte finish appearance. Very high spread
rates (750-4000 sq. ft. per gallon based upon the porosity of the
primed/sealed surface) make ONE COAT™ also an economical
choice.
ONE COAT™ can be also used to seal all types of metal, plastic,
painted, vinyl, and leather materials and more to prevent damage from
SUN, WATER, and most CHEMICALS. This includes leather and vinyl,
furniture, stainless steel, telephone booths. Pre-sealed wooden
objects can be waterproofed and protected with ONE COAT™.
Because dust, dirt, and many chemicals cannot penetrate nor harm ONE
COAT™, sealed objects are now water and stain resistant and very
easy to clean with just water.
ONE COAT™ will prevent the frequent oxidizing of Brass and
eliminate the high labor costs of frequent brass polishing. Brass
will not need any brass polish. Our product can be used on top of the
lacquer on the brass or on unlacquered brass. Be certain to remove
any oily brass polishing on the brass or on the lacquer on the brass
before applying ONE COAT™ because oil and water do not mix! Our
water based product will run on oily brass. Less costly protection is
also made possible when it is applied to metals such as aluminum and
steel to eliminate the need for expensive cleaning chemicals and high
labor cost cleaning work -permanently! ONE COAT™ also makes
vehicle finishes look better. The high gloss can last for years!
|
|
|
The following pictures demonstrate how ONE COAT™ beautifies wood panelling and how it protects the wood from water damage.
Click on any
of the pictures to see them in full
size.
 Wood panel previously treated with wood stain. |
 Left side of panel sealed with 4 coats of ONE COAT™. |
 Wet glass with water placed for 10 minutes on top of wood panel, one half on sealed side with ONE COAT™, and the other half on unsealed side of panel. |
 Glass removed: water beaded up on top of ONE COAT™ and it did not penetrate into the wood. The unsealed part of wood darkened, which means that water has penetrated in the wood, which leads to water stains and water to damage. |
MAIN USES FOR ONE COAT™:
ONE
COAT™ is safe and pleasant to use as directed.
High
spread rates of 2000 sq.ft.- 4000 sq.ft. per gallon
depending on the substrate porosity insure economical use.
ONE
COAT™ will not yellow, peel, flake, chip, nor crack.
Colors will not fade/oxidize. ONE
COAT™ protects and restores old house paint pigments
and prevents new paints from fading. ONE
COAT™ also enhances the look on all applied
paints/materials/substrates. There is
no evidence of UV damage, or other damage on sealed surfaces
for over 9 years! Our
sealers/finishes are unaffected by high heat, water, salt
water, wind, rain, acids, and food liquid spills. VOC COMPLIANT: Only 19.6 g/l per California VOC Regulations WARRANTED
FOR 5 YEARS!* ONE COAT™ PRODUCT
DATA SHEET
DESCRIPTION AND
USE:
ONE COAT™ is an aqueous
emulsion of modified thermoplastic resins and their esters. It is
ready to use and has an indefinite shelf life. The product has a
gloss of 90 on the Gardner Scale, and it is also available in a (No
Gloss) version to produce a satin/matte finish.
ONE COAT™ is a water based Primer/Sealer/Finish. It may be
applied to a wide variety of materials and substrates to provide many
years of superior economical protection from Sun, Water and most
Chemical damage. For example, it should be used on MASONRY such as
marble, terrazzo, concrete, grout. STONE such as granite, limestone,
ceramic tile grout and worn ceramic tile and grout and many others
benefit to waterproof and enhance the natural beauty of this and all
other substrates and materials. Plastics, vinyl, composite materials,
metals such as brass, chrome, stainless steel, aluminum, asphalt and
rubber are protected from environmental damage, reduced labor
maintenance costs, and extended life when sealed with ONE COAT™.
Previously sealed wood and other coated surfaces such as floor
finish, varnish, lacquer, epoxy, etc. which are in sound acceptable
looking appearance may be sealed with ONE COAT to eliminate costly
damage/stripping, and to provide a beautiful many years lasting
appearance which can be cleaned with just water eliminating the need
for special cleaning products and the damage of repetitive
cleaning.
The product provides extraordinary benefits when used as a PRIMER before painting, because one coat hides all, especially water stains and graffiti. It DRIES IN MINUTES to save costly labor time, and any type of paint will bond to it and keep it's color integrity while using less paint to do so when painting. Example, use one coat of paint instead of using two coats of paint. Also, a less costly paint may be used as it is now protected from most environmental damage. In addition, ONE COAT™ should be used to protect the house paint and other paints itself after it is dry for the purpose of preventing the paint from fading, peeling, and cracking by applying 4 coats on top of the new or old paint which is in sound condition. ONE COAT™ will bring out the faded/oxidized pigment in old paint on contact, and this restored look will remain for many years.
The product dries quickly, within minutes in many instances with
moving air from a blower or a fan, and with good ventilation. The
product should not be used on any surface which will be underwater
such as swimming pools or the bottoms of boats, for example.
ONE COAT "breathes" allowing moisture vapors to escape while locking
out water. Saltwater has no affect on this product.
It prevents damage to wall grout of all types by preventing
discoloration, efflorescence, mold/mildew/algae, and thereby
eliminates very costly maintenance. When used on new or shiny ceramic
tile and grout, ONE COAT™ protects the grout from becoming
uneven in appearance after numerous cleanings and from staining and
water damage. It can be used inside or outside. It is stain resistant
to urine, gasoline, oil, and acids such as foods and liquid spills.
Its use cost is pennies per sq. ft. compared to $$$ per sq.; ft. for
many other different types of coatings because of the very high
spread rate of ONE COAT™ which is up to 4000 sq.ft. per gallon
depending upon the porosity of the sealed material. Stainless steel,
aluminum, brass, and other metals as well as vinyl benefit from the
use of ONE COAT™ by eliminating the need for expensive cleaning
chemicals, frequent cleaning, damage to the materials by chemicals,
reducing labor maintenance costs, and maintaining the natural
appearance of these materials for years. This is because when these
materials are sealed with ONE COAT™, one is now cleaning the
sealer on the surface of the material and no longer the material
itself. Very often, cleaning ONE COAT™ is efficiently
accomplished with just plain water! Doing so eliminates the film that
cleaning chemicals leave on the sealer which appears to dull the high
gloss. When a cleaning chemical is used to clean ONE COAT™,
simply rinse or wash it off with clean water and you will see the
high gloss of the primer/sealer/finish!
ONE COAT™ does NOT yellow, peel, flake, nor chip. It prevents
rust and corrosion. Sealed materials/substrates will not change in
color or appearance under the cured sealer. The product performance
is proven by many years of industrial use which includes many
prestigious firms. Its chemical composition is unique and unavailable
in other products!
PRODUCT
APPLICATION:
DIRECTIONS FOR USE ON OLD AND NEW PAINTS, HOUSE PAINT, WOODS, VINYL, METALS, SIGNS, WALL COVERINGS, FURNITURE, ALL MASONRY, AND OTHER SMOOTH AND ROUGH MATERIALS AND SUBSTRATES AND OVER OTHER APPLIED COATINGS.
NOTE: USE THE RECOMMENDED SPONGE SYSTEM BELOW. SMOOTH AREAS MAY HAVE BUMPS, GROOVES, INDENTATIONS, ETC. USE A QUALITY SPONGE MOP IF ALL THESE AREAS ARE SMOOTH. A FINE BRISTLED BRUSH CAN BE USED FOR HARD TO REACH AREAS. A urethane type sponge mop is available at hardware/paint/janitorial stores. This is a very soft sponge with no holes on top. It is very resistant to tearing and cracking. It is available with a wringer and on a pole.
Our glossy version of ONE COAT™ does not need shaking. The satin/matte finish version requires vigorous shaking in small containers. Use an electric drill to mix it in 5 gallon pails for about 5 minutes. Test mixed material appearance after mixing by spreading it on a small inconspicuous area. The appearance should look dull.
USE ONE COAT™ AS A PRIMER ON WALLS AND ON ALL OBJECTS BEFORE APPLYING NEW PAINT TO PREVENT WATER DAMAGE TO THE PAINT FROM BELOW.
1. Pre-clean all materials (new or used) with a neutral cleaner (PH of 7) to degrease and remove all soils and residues before sealing with ONE COAT™. Allow cleaned area to dry. Use a fan indoors to speed drying.
ON SMOOTH AREAS:
2. For small areas, apply product directly to sponge mop and squeeze out excess into clean tray or bucket. For larger areas, pour product into tray or bucket. Dip sponge mop directly into product and squeeze out excess with handle. Sponge mop should be damp with product, not soaking, nor dripping.
3. Apply product dampened sponge mop directly to the paint/material to be sealed and draw the sponge across the surface. Treated area should look wet. Do not rub the product on the area! Doing so can disturb the film which forms quickly! Blend in any "runs" or "drips immediately. Continue applying the product until you cannot see the wetness of the product. Dip the sponge mop back into the product, squeeze out excess product, and continue the application.
4. Start at the top far end and move the wet sponge mop across from one end to the other. Then, repeat this technique until you have reached the bottom. Use sponge mop with or without pole for convenience.
5. We suggest that you apply 4 separate coats for best appearance and performance on any material or paint. Allow each coat to thoroughly dry to the touch before applying the next coat.
6. Allow 96 hours for the product to cure. This means that the non water elements will harden to allow water cleaning and normal use. Moving air is essential to the drying and curing process! Do not apply the product outdoors in dusty conditions nor if it is likely to rain within a few days!
7. Rinse the sponge mop in water to avoid it being sealed and ruined by the drying sealer after use.
ON ROUGH MATERIALS SUCH AS
BRICK:
1. Use an airless sprayer with 13" or 15" reversible tip at 300-500 psi. Or, use a clean brush.
2. Spray mist the product over the area. Seeing the wetness of the product as applied is sufficient coverage for each coat.
3. When the first coat is "dry to the touch", repeat the procedure above to apply the additional coats.
VERY IMPORTANT:
Do not use yellow colored sponges either new or used with rough surfaces to spread ONE COAT™. Use a smooth surface urethane type sponge material, which is commonly available at hardware/paint, and at janitorial supply stores. Pre-rinse the sponge and allow it to thoroughly dry before dipping it in ONE COAT™. Use a painters foam pad brush for applying ONE COAT™ to walls and for touch ups to any area. Rinse and allow the foam pad brush to dry out before use.
Keeping the sponge/pad resting in a quantity of WET ONE COAT™, as in the bottle/container, will prevent the sponge/pad from drying out while you are waiting for any single coat of ONE COAT™ to dry out thoroughly on the floor/wall. The sponge/pad will NOT dry out in wet SKID SAFE as long as there is wet ONE COAT™ soaking the entire area of the sponge/pad! Wring out excess wet ONE COAT™ from the sponge/pad before applying the next coat so that the tool is damp with ONE COAT™, not dripping wet in ONE COAT™.
It is extremely important NOT to rub ONE COAT™ around on the floor or wall with the tool! Simply move the tool across the area in one direction until you do not see any more wetness, then, rewet in ONE COAT™, and continue. Allow each coat to be thoroughly DRY TO THE TOUCH before applying the next coat. If you choose to apply SKID SAFE directly into your grout lines, use a foam pad.
REASONS WHY:
Manufacturers often add chemicals to these tools, which DO INTERFERE with the proper performance of SKID SAFE. It is possible to adversely disturb the previous applied coat with the next coat if you rub SKID SAFE over it. DO NOT go "back and forth" with the tool!
MAINTENANCE:
1. Clean cured treated areas with
plain water. Use our New
Dimensions DISAPPEAR™ Organic Graffiti/Adhesive
Remover to clean graffiti,
adhesives and decals. Rinse area with clean water after
cleaning.
2. Reapply sealer to any needed
area after graffiti, adhesive, decal cleaning.
3. Pressure washing will not affect
our products! Do not use highly alkaline cleaning products! High
gloss can be brightened-even years later-by burnishing area with a
soft cloth, or simply reapply another coat of our product!
TECHNICAL
DATA:
FORM: Milky White Liquid
Active Material (Solid) Content: 15%
Specific Gravity: 1.04
Weight per Gallon: 8.6 lbs.
Flash Point: Non-Combustible
Carry Agent: Water
Shelf Life: Indefinite
Repellency Rating (ASTM C 67): EXCELLENT
Pencil Hardness (ASTM D 3363): 2H
Tukon Hardness (ASTM D 1474): 14
Flexibility (ASTM D 1737 ): 1/8" mandrels: 3
Adhesion: (ASTM D 3359 ): FAIR-GOOD
lonic Charge: Anionic
Thermal Shock: (ASTM D 1211): 3 cycles
SKID RESISTANCE: (ASTM C 1028) DRY: COF =.81, WET: COF = .77
HEAT RESISTANCE: No affect up to 600 degrees F
Gloss: 90
Exterior/Interior Durability: EXCELLENT
NON COMBUSTIBLE
VOC: 19.6 grams/litre per California VOC Regulations
ODOR: Extremely Mild
CURE TIME: 96 HOURS
BENEFITS IN
SUMMARY:
Prevents discoloration and deterioration
Protects house paint and saves
several house painting cycles
Prevents oxidation, rust and corrosion, mold, mildew and UV
damage
Waterproofs and Breathes
Resists damage from salt water
Buffable
Does not require stripping
Penetrates into porous surfaces - it is very tough grout sealer and
concrete sealer
Gloss and Protection endures for years
Satin/Matte finish to HIGH GLOSS
Prevents common types of damage to grout.
Resists staining from water, oils, gasoline, acids, grease, dirt,
salt water, food and beverage spills including alcohol, acids, and
uric acid when cured.
Reduces labor costs associated with cleaning hard to clean surfaces
and prevents surface damage.
Revitalizes old faded surfaces.
Recommended for sealed wood, under and over any paint, masonry,
metals, plastics, etc.
New applications blend into old applications
Does not yellow, peel, flake, crack, nor chip.
Guaranteed 5 years on walls or on any object with proper application
and maintenance.
Benefits last for many YEARS.
ONE COAT™ is but one of our many fine exclusive products
specifically designed to solve problems for which solutions are
difficult or impossible to find which we have been successfully
marketing to industry since 1986.
|
|
|
 |
|
|
|
|
CLICK
PRICE BELOW TO ORDER ONE COAT™:
|
|
|
|
per unit |
per case |
 Water Based Primer/Sealer/Finish |
QUART (32 oz) |
|
|
|
|
CASE of 12 QUARTS |
|
|
|
|
|
GALLON (128 oz) |
|
|
|
|
|
CASE of 4 GALLONS |
|
|
|
|
|
5-GALLON PAIL |
|
|
|
|
|
|
|
|||
The pictures below demonstrate how can ONE COAT™ restore old/faded paint on garage door into new looking paint.
Newly sealed surfaces will stay looking beautiful, and will be protected from Sun, Water and other elements for many years.
 5 years old faded garage door |
 Same door sealed (not painted) with ONE COAT™ |
|
|
|
 "Excellent product! Easy to apply, and the odor so insignificant, that I was able to apply to a busy interior stairwell with a constant stream of guests walking by. As you can see in the attached photo, we applied your product over the newly painted graphics. We are not very concerned about actual graffiti, but with this stairwell connecting the main lobby of the Aspen Recreation Center and the Lewis Ice Arena we have many sticky little fingers, hockey bags, hockey sticks, skates and up to 1,000 people a day using these stairs. The Plant and Engineering manager is so impressed with your product, he is considering its use throughout the entire facility.July 25, 2006 - John D. Hoepfer, Peach Moon Studios, Aspen, Colorado |
|
*FIVE YEAR WARRANTY:
Your purchase of any of our primers/sealers/finishes/coatings are warranted to perform according to our specifications when applied and maintained according to our directions for 5 years. Abuse of our products is not covered under this warranty. High gloss is not covered under this warranty. Misuse nor misapplication nor poor maintenance is not covered under this warranty. Your rights under this warranty are not transferrable. Only the original buyer may file a claim with us under this warranty. If we determine the validity of a claim under this warranty, we will refund or replace the product(s) at your option less the time that the product(s) performed from the 5 year period. Example: If the product performed for 2.5 years, you could receive a refund of half the product cost, or replace the product at a credit of half of the List Price towards replacement.
LIMITATION OF LIABILITY: The user assumes full responsibility and risk in testing this product for the particular application and for determination of proper disposal method of chemical residues and cleaning implements according to State and Federal regulations. In no event shall New Dimensions Solutions, LLC be liable for consequential or incidental damages exceeding the cost of this product.
 |
|
If you prefer,
there are 3 other ways to place your
order:
1. By
FAX:
(866) 361-1558 2. By mail:
New Dimensions Solutions, LLC,3960 Howard Hughes Parkway, Suite 500, Las Vegas, NV 89169 3. By calling (800) 731-2231 Monday - Friday, between 9 - 5 p.m. PST.
All Our Products
Are Proudly Made In The U.S.A.
